Monel 400 Bolts

Monel 400 Bolts

Monel 400 is a Nickel Bolts-copper compound (about 67% Ni – 23% Cu) that is impervious to ocean water and steam at high temperatures just as to salt and burning arrangements. Monel 400 is a strong arrangement compound that must be solidified by virus working. This Nickel Bolts composite shows qualities like great consumption opposition, great weldability and high quality. A low consumption rate in quickly streaming bitter or seawater joined with incredible protection from stress-erosion splitting in many freshwaters, and its protection from an assortment of destructive conditions prompted its wide use in marine applications and other non-oxidizing chloride arrangements. This Nickel Bolts amalgam is especially impervious to hydrochloric and hydrofluoric acids when they are de-circulated air through. As would be normal from its high copper content, combination 400 is quickly assaulted by nitric corrosive and smelling salts frameworks.

stainless-steel-monel-400-manufacturer-supplier-importer-exporter-stockholder

Monel 400 has extraordinary mechanical properties at below zero temperatures, can be utilized in temperatures up to 1000° F, and its dissolving point is 2370-2460° F. Be that as it may, compound 400 is low in quality in the strengthened condition in this way, an assortment of tempers might be utilized to expand the quality

Alloy 400 is for all intents and purposes safe to chloride particle push erosion splitting in run of the mill situations. By and large, its erosion obstruction is great in lessening situations, however poor in oxidizing conditions. It isn't helpful in oxidizing acids, for example, nitric corrosive and nitrous. By and by, it is impervious to most antacids, salts, waters, sustenance items, natural substances and barometrical conditions at typical and raised temperatures.

This Nickel Bolts combination is assaulted in sulfur-bearing gases above roughly 700° F and liquid sulfur assaults the composite at temperatures over around 500° F. Monel 400 offers about indistinguishable erosion opposition from Nickel Bolts yet with higher greatest working weights and temperatures and at a lower cost because of its better capacity than be machined.

 

Monel 400 Bolts Specifications

Material : Monel 400
Standard : DIN, ASTM, BS and all International Standards
Length : 3 mm to 200 mm
Size : M3 – M56 | 3/6″ to 2″ | Custom Sizes
Type : Hex Head Bolts, Square Bolts, U bolts, Eye bolts, T bolt, Hex Bolt, Lag Bolts, Counter sunk Bolts, Hex Head nuts, Square nuts, Lock nuts, Eye nuts, wing nuts, T nuts, Panel Nuts, Coupling Nuts, Dome nuts, Acorn Nuts.

 

Types of Monel 400 Bolts

Monel Hex Head Bolt Monel Alloy Hex Head Bolt
Monel Hex Head Bolt
Monel 400 Hex Head Bolt
Monel Square Bolt Monel Alloy Square Bolt
Monel Square Bolt
Monel 400 Square Bolt
Monel U Bolt Monel Alloy U Bolt
Monel U Bolt
Monel 400 U Bolt
Monel Eye Bolt Monel Alloy Eye Bolt
Monel Eye Bolt
Monel 400 Eye Bolt
Monel T Bolt Monel Alloy T Bolt
Monel T Bolt
Monel 400 T Bolt
Monel Hex Bolt Monel Alloy Hex Bolt
Monel Hex Bolt
Monel 400 Hex Bolt
Monel Lag Bolt Monel Alloy Lag Bolt
Monel Lag Bolt
Monel 400 Lag Bolt
Monel Counter sunk Bolt Monel Alloy Counter sunk Bolt
Monel Counter sunk Bolt
Monel 400 Counter sunk Bolt

 

Applications of Monel 400 Bolts

Marine engineering
Chemical and hydrocarbon processing equipment
Gasoline and freshwater tanks
Crude petroleum stills
De-aerating heaters
Boiler feed water heaters and other heat exchangers
Valves, pumps, shafts, fittings, and fasteners
Industrial heat exchangers
Chlorinated solvents
Crude oil distillation towers

 

ASTM Specifications of Monel 400 Bolts

Pipe Smls Pipe Welded Tube Smls Tube Welded Sheet/Plate Bar Forging Fitting Wire
B165 B725 B163   B127 B164 B564 B366  

 

Mechanical Properties of Monel 400 Bolts

Product Form

Condition Tensile (ksi) .2% Yield (ksi) Elongation (%) Hardness (HRB)
Rod & Bar Annealed 75-90 25-50 60-35 60-80
Rod & Bar Cold-Drawn Stress Relieved 84-120 55-100 40-22 85-20 HRC
Plate Annealed 70-85 28-50 50-35 60-76
Sheet Annealed 70-85 30-45 45-35 65-80
Tube & Pipe Seamless Annealed 70-85 25-45 50-35 75 max *

 

COATINGS

 

OUR SUMMARY :
Review Date
Reviewed Product
Monel 400 Bolts
Author Rating

 

Domestic Area


Our Export

Get a Quote

Request A Quote